Projects/Micro Reflow Oven: Difference between revisions
Jump to navigation
Jump to search
(→Design) |
m (Peter moved page Micro Reflow Oven to Projects/Micro Reflow Oven without leaving a redirect) |
||
| (2 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
[[category:Projects]] | |||
The goal is to be able to easily and cheaply produce small SMD PCB boards at home. <videoflash>o_SwxI2KTys</videoflash> | The goal is to be able to easily and cheaply produce small SMD PCB boards at home. <videoflash>o_SwxI2KTys</videoflash> | ||
| Line 27: | Line 28: | ||
== Design 1 == | == Design 1 == | ||
In this approach the micro controller unit (MCU) controls a heat source to regulate the temperature. | |||
<uml> | <uml> | ||
[Circuit Board] as PCB | [Circuit Board\n(Componentized PCB)] as PCB | ||
[PCB Temperature\n(Thermocouple Type K)] as T1 | [PCB Temperature\n(Thermocouple Type K)] as T1 | ||
[Room Temperature\n(Thermocouple Type K)] as T2 | [Room Temperature\n(Thermocouple Type K)] as T2 | ||
[ADC\n(ADS1115)] as ADC | [ADC\n(ADS1115)] as ADC | ||
[MCU\n(ESP8266)] as MCU | [MCU\n(ESP8266)] as MCU | ||
[Hot Air\n(Heater)] as H | |||
[UI\n(Tablet/SmartPhone)] as UI | [UI\n(Tablet/SmartPhone)] as UI | ||
Actor User as USER | Actor User as USER | ||
[PCB] ..> [T1] | [PCB] ..> [T1] | ||
[PCB] <. [H] | [PCB] <. [H] | ||
| Line 47: | Line 50: | ||
== Design 2 == | == Design 2 == | ||
In this approach the heat source is constant and the micro controller unit (MCU) controls an air mixer to regulate the temperature. | |||
<uml> | <uml> | ||
[Circuit Board] as PCB | [Circuit Board\n(Componentized PCB)] as PCB | ||
[PCB Temperature\n(Thermocouple Type K)] as T1 | [PCB Temperature\n(Thermocouple Type K)] as T1 | ||
[Room Temperature\n(Thermocouple Type K)] as T2 | [Room Temperature\n(Thermocouple Type K)] as T2 | ||
| Line 54: | Line 59: | ||
[MCU\n(ESP8266)] as MCU | [MCU\n(ESP8266)] as MCU | ||
[UI\n(Tablet/SmartPhone)] as UI | [UI\n(Tablet/SmartPhone)] as UI | ||
[ | [Hot Air\n(Heater)] as H | ||
[Air | [Cold Air\n(Ventilator)] as V | ||
[ | [Air Mixer\n(Servo Motor)] as M | ||
Actor User as USER | Actor User as USER | ||
[PCB] ..> [T1] | [PCB] ..> [T1] | ||
| Line 63: | Line 68: | ||
[ADC] -> [MCU] | [ADC] -> [MCU] | ||
[H] ..> [M] | [H] ..> [M] | ||
[ | [V] ..> [M] | ||
[ | [M] <-- [MCU] | ||
[MCU] <-- [T2] | [MCU] <-- [T2] | ||
[MCU] <.> [UI] | [MCU] <.> [UI] | ||
[UI] <.> USER | [UI] <.> USER | ||
</uml> | </uml> | ||
Latest revision as of 02:07, 17 May 2016
The goal is to be able to easily and cheaply produce small SMD PCB boards at home.
The Challenge
Create a device to run a PCB though a temperature profile. Requirements and constraints:
| Parameters | Priority | Notes |
|---|---|---|
| 1.5 x 1 inch PCB size, 0.75 inch height | MUST | Targeted at small SMD boards only. |
| Close loop temperature control | MUST | Peek temperature is 260C / 500F. |
| Programmable temperature profile | MUST | |
| Wifi connected | MUST | This is to log the actual temperature profile |
| Live chart | MUST | |
| Portable i.e. it fits in a pocket | want | |
| Battery powered | want | The heat source could be external e.g. stove, heatgun, iron, solar, ... |
| Live video stream | want | Ideally overlaid with current temperature. |
| TFT screen and buttons | want | Touch screen preferred. Rotary encoder ok. |
Design 1
In this approach the micro controller unit (MCU) controls a heat source to regulate the temperature.
Design 2
In this approach the heat source is constant and the micro controller unit (MCU) controls an air mixer to regulate the temperature.