Projects/Micro Reflow Oven: Difference between revisions
Jump to navigation
Jump to search
(Created page with "The goal is to be able to easily and cheaply produce small SMD PCB boards at home. <videoflash>o_SwxI2KTys</videoflash> == The Challenge == Create a device to run a PCB thou...") |
m (Peter moved page Micro Reflow Oven to Projects/Micro Reflow Oven without leaving a redirect) |
||
| (5 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
[[category:Projects]] | |||
The goal is to be able to easily and cheaply produce small SMD PCB boards at home. <videoflash>o_SwxI2KTys</videoflash> | The goal is to be able to easily and cheaply produce small SMD PCB boards at home. <videoflash>o_SwxI2KTys</videoflash> | ||
| Line 5: | Line 6: | ||
{| class="wikitable" | {| class="wikitable" | ||
|- | |- | ||
! | ! Parameters !! Priority !! Notes | ||
|- | |- | ||
| 1.5 x 1 inch PCB size, 0.75 inch height || MUST || Targeted at small SMD boards only. | | 1.5 x 1 inch PCB size, 0.75 inch height || MUST || Targeted at small SMD boards only. | ||
|- | |- | ||
| Close loop temperature control || MUST || | | Close loop temperature control || MUST || Peek temperature is 260C / 500F. | ||
|- | |- | ||
| Programmable temperature profile || MUST || | | Programmable temperature profile || MUST || | ||
| Line 26: | Line 27: | ||
|} | |} | ||
== Design == | == Design 1 == | ||
In this approach the micro controller unit (MCU) controls a heat source to regulate the temperature. | |||
<uml> | <uml> | ||
[Circuit Board] as PCB | [Circuit Board\n(Componentized PCB)] as PCB | ||
[PCB Temperature\n(Thermocouple Type K)] as T1 | [PCB Temperature\n(Thermocouple Type K)] as T1 | ||
[Room Temperature\n(Thermocouple Type K)] as T2 | [Room Temperature\n(Thermocouple Type K)] as T2 | ||
[ADC\n(ADS1115)] as ADC | [ADC\n(ADS1115)] as ADC | ||
[MCU\n(ESP8266)] as MCU | [MCU\n(ESP8266)] as MCU | ||
[Hot Air\n(Heater)] as H | |||
[UI\n(Tablet/SmartPhone)] as UI | [UI\n(Tablet/SmartPhone)] as UI | ||
Actor User as USER | Actor User as USER | ||
[PCB] ..> [T1] | [PCB] ..> [T1] | ||
[PCB] <. [H] | [PCB] <. [H] | ||
| Line 46: | Line 49: | ||
</uml> | </uml> | ||
== Design 2 == | |||
In this approach the heat source is constant and the micro controller unit (MCU) controls an air mixer to regulate the temperature. | |||
<uml> | |||
[Circuit Board\n(Componentized PCB)] as PCB | |||
[PCB Temperature\n(Thermocouple Type K)] as T1 | |||
[Room Temperature\n(Thermocouple Type K)] as T2 | |||
[ADC\n(ADS1115)] as ADC | |||
[MCU\n(ESP8266)] as MCU | |||
[UI\n(Tablet/SmartPhone)] as UI | |||
[Hot Air\n(Heater)] as H | |||
[Cold Air\n(Ventilator)] as V | |||
[Air Mixer\n(Servo Motor)] as M | |||
Actor User as USER | |||
[PCB] ..> [T1] | |||
[PCB] <. [M] | |||
[T1] -> [ADC] | |||
[ADC] -> [MCU] | |||
[H] ..> [M] | |||
[V] ..> [M] | |||
[M] <-- [MCU] | |||
[MCU] <-- [T2] | |||
[MCU] <.> [UI] | |||
[UI] <.> USER | |||
</uml> | |||
Latest revision as of 02:07, 17 May 2016
The goal is to be able to easily and cheaply produce small SMD PCB boards at home.
The Challenge
Create a device to run a PCB though a temperature profile. Requirements and constraints:
| Parameters | Priority | Notes |
|---|---|---|
| 1.5 x 1 inch PCB size, 0.75 inch height | MUST | Targeted at small SMD boards only. |
| Close loop temperature control | MUST | Peek temperature is 260C / 500F. |
| Programmable temperature profile | MUST | |
| Wifi connected | MUST | This is to log the actual temperature profile |
| Live chart | MUST | |
| Portable i.e. it fits in a pocket | want | |
| Battery powered | want | The heat source could be external e.g. stove, heatgun, iron, solar, ... |
| Live video stream | want | Ideally overlaid with current temperature. |
| TFT screen and buttons | want | Touch screen preferred. Rotary encoder ok. |
Design 1
In this approach the micro controller unit (MCU) controls a heat source to regulate the temperature.
Design 2
In this approach the heat source is constant and the micro controller unit (MCU) controls an air mixer to regulate the temperature.