Projects/Micro Reflow Oven: Difference between revisions

From Playful Exploration
Jump to navigation Jump to search
m (Peter moved page Micro Reflow Oven to Projects/Micro Reflow Oven without leaving a redirect)
 
(3 intermediate revisions by the same user not shown)
Line 1: Line 1:
[[category:Projects]]
The goal is to be able to easily and cheaply produce small SMD PCB boards at home.  <videoflash>o_SwxI2KTys</videoflash>
The goal is to be able to easily and cheaply produce small SMD PCB boards at home.  <videoflash>o_SwxI2KTys</videoflash>


Line 26: Line 27:
|}
|}


== Design ==
== Design 1 ==
In this approach the micro controller unit (MCU) controls a heat source to regulate the temperature.
 
<uml>
<uml>
[Circuit Board] as PCB
[Circuit Board\n(Componentized PCB)] as PCB
[PCB Temperature\n(Thermocouple Type K)] as T1
[PCB Temperature\n(Thermocouple Type K)] as T1
[Room Temperature\n(Thermocouple Type K)] as T2
[Room Temperature\n(Thermocouple Type K)] as T2
[ADC\n(ADS1115)] as ADC
[ADC\n(ADS1115)] as ADC
[MCU\n(ESP8266)] as MCU
[MCU\n(ESP8266)] as MCU
[Hot Air\n(Heater)] as H
[UI\n(Tablet/SmartPhone)] as UI
[UI\n(Tablet/SmartPhone)] as UI
Actor User as USER
Actor User as USER
[Heater] as H
[PCB] ..> [T1]
[PCB] ..> [T1]
[PCB] <. [H]
[PCB] <. [H]
Line 46: Line 49:
</uml>
</uml>


http://www.claustemp.com/an-htp15.htm
== Design 2 ==
In this approach the heat source is constant and the micro controller unit (MCU) controls an air mixer to regulate the temperature.
 
<uml>
[Circuit Board\n(Componentized PCB)] as PCB
[PCB Temperature\n(Thermocouple Type K)] as T1
[Room Temperature\n(Thermocouple Type K)] as T2
[ADC\n(ADS1115)] as ADC
[MCU\n(ESP8266)] as MCU
[UI\n(Tablet/SmartPhone)] as UI
[Hot Air\n(Heater)] as H
[Cold Air\n(Ventilator)] as V
[Air Mixer\n(Servo Motor)] as M
Actor User as USER
[PCB] ..> [T1]
[PCB] <. [M]
[T1] -> [ADC]
[ADC] -> [MCU]
[H] ..> [M]
[V] ..> [M]
[M] <-- [MCU]
[MCU] <-- [T2]
[MCU] <.> [UI]
[UI] <.> USER
</uml>

Latest revision as of 02:07, 17 May 2016

The goal is to be able to easily and cheaply produce small SMD PCB boards at home.

The Challenge

Create a device to run a PCB though a temperature profile. Requirements and constraints:

Parameters Priority Notes
1.5 x 1 inch PCB size, 0.75 inch height MUST Targeted at small SMD boards only.
Close loop temperature control MUST Peek temperature is 260C / 500F.
Programmable temperature profile MUST
Wifi connected MUST This is to log the actual temperature profile
Live chart MUST
Portable i.e. it fits in a pocket want
Battery powered want The heat source could be external e.g. stove, heatgun, iron, solar, ...
Live video stream want Ideally overlaid with current temperature.
TFT screen and buttons want Touch screen preferred. Rotary encoder ok.

Design 1

In this approach the micro controller unit (MCU) controls a heat source to regulate the temperature.

Adobe SVG Viewer plugin (for Internet Explorer) or use Firefox, Opera or Safari instead.

Design 2

In this approach the heat source is constant and the micro controller unit (MCU) controls an air mixer to regulate the temperature.

Adobe SVG Viewer plugin (for Internet Explorer) or use Firefox, Opera or Safari instead.