Projects/ESP8266 - Pressure (BMP085) Temperature Humidity (DHT22)): Difference between revisions
Jump to navigation
Jump to search
No edit summary |
No edit summary |
||
| Line 1: | Line 1: | ||
[[category:ESP]] | [[category:ESP]] | ||
Version 1 of the quick'n-dirty weather station is online for the first 24 hours, running on a | Version 1 of the quick'n-dirty weather station is online for the first 24 hours, running on a USB power stick, sending air pressure, temperature and humidity data from the balcony up directly to the VPS's influxdb. No mptt, just simple http web requests. Version 2 will need some enclosure to protect the electronic from the elements. | ||
Graphical output using Grafana: https://www.playfulexploration.com/grafana/dashboard/db/pressure-temperatur-humidity-5min-interval | |||
[[File:ESP8266 - Pressure Temperature Humidity.JPG|300px|right]] | [[File:ESP8266 - Pressure Temperature Humidity.JPG|300px|right]] | ||
Revision as of 14:07, 19 February 2016
Version 1 of the quick'n-dirty weather station is online for the first 24 hours, running on a USB power stick, sending air pressure, temperature and humidity data from the balcony up directly to the VPS's influxdb. No mptt, just simple http web requests. Version 2 will need some enclosure to protect the electronic from the elements.
Graphical output using Grafana: https://www.playfulexploration.com/grafana/dashboard/db/pressure-temperatur-humidity-5min-interval
Features
- AMS1117-3.3 Voltage Regulator
- Microcontroller ESP8266
- Firmware Lua NodeMCU
- Sensor driver build into the firmware
- DHT22 Temperature and Humidity Sensor, sensor specific single wire protocol
- BMP280 Barometric Pressure Sensor, I2C
- CP2102 USB to UART Adapter
Http-Requests based Data Push to Influxdb
| file | lua code | Notes |
|---|---|---|
| config.lua | wifi.setmode(wifi.STATION)
wifi.sta.config("SSID","PASSWORD")
wifi.sta.connect()
|
setup file, connects the esp to the router |
| init.lua | print("\n\nHold gpio0 low to stop boot")
tmr.delay(1000000)
if gpio.read(3) == 0 then print("...boot stopped") return end
print("...booting", collectgarbage('count'))
print('ready',collectgarbage('count'))
dofile('config.lc')
|
Startup code that allows stopping the boot by holding GPIO0 low. |
| init.lua | -- restart if stall
tmr.softwd(30)
--bmp085.init( dofile("i2c_locate.lc") )
bmp085.init( 6, 5 )
print( bmp085.pressure(), bmp085.temperature()/10, dht.read(7) )
trigger = nil
conn = nil
pub = function(c)
local d="pa val="..bmp085.pressure()
local s,t,h=dht.read(7)
if s==0 then d=d.."\ntemp val="..t.."\nhumi val="..h end
local m="POST /write?db=rocket HTTP/1.1\r\nContent-Length: "..d:len().."\r\nContent-Type: application/x-www-form-urlencoded\r\n\r\n"..d
print(m)
c:send(m)
end
trigger = function(c)
conn = net.createConnection(net.TCP, 0)
conn:on("connection", pub)
conn:on("receive", function(conn,m) conn:close() conn=nil print(m) tmr.alarm(0, 3000, 0, trigger) tmr.softwd(30) end)
conn:connect(8086,"playfulexploration.com")
end
trigger()
|
Net client connects to influxdb every 3 seconds and send data |